DPL-Surveillance-Equipment.com   /     How To Avoid Thermal Imaging Cameras

Description

Click Here Or On Above Image To Reach Our ExpertsHow To Avoid Thermal Imaging CamerasNow this was written to help the military snipers to be able to blend in, and avoid Thermal Imaging Cameras. It does an awesome job of explaining how they work And their weak points etc. Well we can also use the same principles talked about here, to help those of you who need to avoid the detection by Thermal Heat Detecting Cameras.Knowledge Is PowerThermal Detection, there are some pretty gloomy postings about IR detection. As a security/surveillance expert, I might shed some light (pun intended) on the subject. To qualify this, I am using the latest (I think) commercially available FLIR product. These are my observations about IR imagers using the latest thermal imaging equipment. This is about THERMAL imaging avoidance.IR is not Xray, Hollywood be damned-it cannot detect a differential heat image through common solid materials, plastic film (black or otherwise) being an exception. PRO-DTECH II FREQUENCY DETECTOR(Buy/Rent/Layaway)However, a good imager system can see through holes in a masking material ("IR masking" camo net). And if you are inside a dumpster, body heating the bad guy's side, he can "see" the hot spot on the dumpster's outside. But if you are not leaning (heating) against that side, he can't "see you". Your body heat will not be detected behind most readily available unholed blinding materials if you are not differentially warming/cooling those materials or allowing your own IR to reflect off of something behind/over you. BUT, if the shielding materials are alien to the surroundings, the material itself will probably stand out.See Below:Glass will not allow your THERMAL image to transmit (pass) through; same as the dumpster scenario. The lenses of IR imagers are made of exotic nonglass materials because of this.CELLPHONE DETECTOR (PROFESSIONAL)(Buy/Rent/Layaway)Every piece (cluster) of matter, including gasses, emits IR if it is above Absolute Zero (minus 459.69 degrees F). The warmer a body gets, the more IR it will emit. Eventually it will enter the visible spectrum as it gets "red hot".PRO-DTECH III FREQUENCY DETECTOR(Buy/Rent/Layaway)The surface of a piece of matter is where IR is emitted. Altering an object's surface will alter the rate at which IR is emitted. Stoveblack is a classic example.Materials physically different from each other will likely emit IR at different rates. BUT the differences may be very slight.PRO-DTECH III FREQUENCY DETECTOR(Buy/Rent/Layaway)IR imaging (read DETECTION) depends upon two objects having one or more differences in Temperature, Emissivity/Reflectivity, and Absorption of the compared objects. For this application, we can forget about Absorption, and you should all understand Temperature. Now, E + R = 100%, thus the more emissive a surface is, the less reflective. If two dissimilar objects are at the same temperature, a high E will "look" hotter to an IR imager than a low E, thus forming an image. Objects with different Temperatures and the right E's could "look" the same, thus forming NO image. Two objects with similar temperatures and similar emissivities will present an unclear, poorly defined image. Herein lies your IR strength.Here are some Emissivity values for a few materials, all in percents, all plus/minus a point or two. These are for short wavelength commercial imagers and may vary slightly for long wavelength/long range military/LE equipment. Military techies should have similar emissivity tables for your equipment. PRO-DTECH III FREQUENCY DETECTOR(Buy/Rent/Layaway)* Human Skin: 97* Black Vinyl Electrical Tape: 97* Surface Sprayed With Dr. Scholl's Aerosol Foot Powder: 96* Water: 95* Rubber, Black, Hard: 94* Glass, Smooth: 94* Plywood, Raw Lumber: 90-95* Most Painted Surfaces (Non Aluminum Paint): 90-95* Aluminum Based Paints, Depending On Formula: 30-50* Oxidized (Blued, Parkerized) Steel: Around 90* Snow: 82-85* "Most" Organics (Vegetation): Around 80* Cloth, Untreated: Around 80 * Sand: 76 Clay: 40* Gravel: 38* Aluminum, Bare And "Shiny" (Read "Spaceblanket"): Under 10Note the materials that cluster around 95, 80, 40, and 10 Now, to apply IR-101: In all of the scenarios below, remember that your body (or ANYTHING above absolute zero) emits IR in ALL directions. If there is a reflective object behind or beside you, it will pick up your IR and reflect it like you were a light bulb. Whichever situation and methods you use, if you have the opportunity, have an ally check you out from a flank with your best IR detection equipment. Or get the flyboys to check you out with FLIR's namesake. Do this by day AND night, as the sun will do weird (but predictable) things to the differential temps.WIRELESS/WIRED HIDDENCAMERA FINDER III(Buy/Rent/Layaway)The BEST way to protect yourself from IR detection is get behind/under what is already there, and DON'T change the temperature of it. Since you obviously have to see and perhaps reach out, do so through the smallest portal(s) you can handle. Those "man-sized" targets detectable at 1100 yards are just that - man-sized -not the size of your nose and right eye. Remember that glass reflects some IR (100 - 94 = 6%), and the sky (space) is cold (approaching Absolute Zero), so if your scope is reflecting not sun, but sky, it will look COLD. If you have on a scope sunshade that is hot, the internal IR of the sunshade will reflect out as HOT.PRO-DTECH IV FREQUENCY DETECTOR(Buy/Rent/Layaway)I believe the GI Woodland BDU's are treated with an IR emittance reducer. If so, the "cloth" E figure in the table will change and you have to adjust for the following discussion. Or obtain untreated camo fabric or defeat that treatment (starch, I believe). The IR reducing treatment makes sense for a situation where the woods is cooler than 98.6 F. I hope the Desert Daylight BDU's are NOT treated, but the nighttime anti-starlight smocks probably should be. If your BDU's image "cold" against hot sand, you are just as "seen". I trust the techies were aware of this, and have specified correctly. But you need to confirm by looking through your equipment at your buddy against some typical backgrounds.It has been reported that "fresh" BDU's do indeed have an IR treatment that fatigues (pun) with laundering in "brightener" detergents. As a hunter, I am aware of the UV problem with animals with good night vision (is it an overabundance of rods, or cones, in the eye?) and there are detergents available via sporting goods stores that do not contain brighteners. If you need to maintain that BDU treatment, you might try that. But again, look at your buddies with your equipment.Now, in sand or vegetation (E = 76-80): If you HAVE to have artificial cover for situations where your clothing will approximate the temperature of the surroundings, you want to expose matching temperature "stuff" with a similar E (around 80). Cover as much of your skin (97) as possible with cloth (80) (remember that I don't know the E for treated BDU's). But also remember that sweaty cloth in a hot, dry background might look cold due to evaporative cooling. If you are in a hot dry situation, a tented, solid (not net), dry camo fabric applied as a screen might do the trick for IR. (Remember, same T, similar E). Visual is another problem. Keep the outlines irregular for both IR and visual. Square stuff in a curvy world stands out, no matter the technology. Fresh local vegetation in front of the screen will help both.Camo face paint is PROBABLY a high emitter, similar to regular paints (90-95), and sweat (water-95) is for sure. You really have to keep that face behind something. I don't know what a synthetic ski mask would have for an E, but I bet it is below 97. A plain old cotton tee shirt mask would work, but remember the wet/dry/cooling problem.Black ANYTHING is a good emitter. Blackened steel barrels, synthetic stocks, and painted surfaces (all E's in the 90's) should be cloth wrapped for IR and visual both. Black SWAT uniforms probably have a higher E than camo. You need to test.Dry rubber boot soles (94) are nearly as hot as your face - sock 'em (80).Old cut local vegetation will be drier, thus HOTTER due to lack of evaporation.The name of this game is to keep both the Emissivity and the Temperature of the screen and clothing the same as that of the surroundings and keep those portals small.If you are on bare clay or gravel (38-40) and are worried about aerial observation, dig in. Cover yourself with almost anything sufficiently rigid and then cover it with at least a thin but full layer of the local "dirt". This will match the E's. Once the moisture of the new cover layer equals the moisture of the surface around you (evaporative cooling), you will be in decent shape IR wise. Remember that these low E materials have a high Reflectivity, so block your own IR from getting out from under the cover. If there is a chance your body heat will affect the top surface of the dirt cover, use insulating material between you and the bottom of the "roof" to keep it the same temp as the ground around you. Foam board or sleeping bags will do that. The most critical times of day for this hide would be as the sun changes, because rapid heating/cooling of a thin layer of dirt will show up compared to the slower heating/cooling of the intact soil masses. If you can set up in a shaded spot where this will not occur, you should be in decent shape. If there is no shade, make the cover layer thick to create a heat sink approaching that of the surroundings.Wireless Camera Finder(Buy/Rent/Layaway)If there is no threat of aerial observation, and it is only a frontal threat, a "wall" of local dirt with small portals would be the best bet.Any new foxhole will print either hot or cold depending on the season and surface temperature, even if the surrounding soil is bare. The deeper soil temp is probably closer to 55 F than the surface.On snow (82-85), build a snow fort or tunnel in and make small portals. Try to dust loose snow to duplicate surface texture. Pray for new snow. If you wore an aluminized face shield behind that snow fort, it would reflect the "cold" off of the fort, and cover your hot face. This might be a shiny side application of the space blanket, and could be worth testing. Water (95) is your breath when it condenses. And it is warmer than the snow. Only thing I can think of to do here is breath through a ski mask and let it condense before it fogs up over your screen.As to "space blanket" applications: there might be some, BUT. If you are using the shiny side toward you to keep your IR from getting out, remember that the backside of it is probably not a good E match to the surroundings and it will heat/cool a lot differently than most natural things around you. If you are trying to put the shiny side out angled down to reflect the IR of the terrain right in front of you, there would be a 10% reduction in the reflection, more if it casts a shadow. If the shiny side is out and up, it will reflect the cold of outer space (or the heat of the sun) - and it is going to look REALLY weird to visual and starlight in EITHER case! I cannot think of a space blanket application that I would stake MY life on.MAGNETIC, ELECTRIC, RADIO ANDMICROWAVE DETECTOR(Buy/Rent/Layaway)In an urban situation, you will have lots of "normal" IR blockers to get under/behind. Just remember that you are an IR light bulb on the cold surfaces behind you. You cannot casually set up back in the room shadows of a windowless building anymore. Remember, glass will NOT pass through (transmit) your IR image. BUT, glass (94) has a high emissivity and will show its surface temperature rather well. If you are near the window warming it with your breath, you will reveal yourself. If you had a small barrel portal through an otherwise intact glass window, you would be IR blocked, but visually seen. A loose pane of glass back in the room shadows might be a possibility, especially for a spotter. If the room is painted (90-95) and warm (approaching 98.6 F), you might blend in IR wise. But if there is one warm window/room in an "empty" building, something is amiss. The painted walls behind you might not reflect your IR really well, but a metallic light fixture might blink every time you turn your face toward it. The best I can imagine is forget about the "room" and get behind/under something that should be there - sofas, chairs, drapes, etc. and keep your portal small.None of the above CONCEALMENT strategies are easy; none are guaranteed to make you disappear to an imager. But they will all help make you a less vivid IR image, thus less detectable. IR imagers may or may not have an adjustment to key in the emissivity for scanning and reading temperatures. I doubt military/LE targeting devices would have that - you don't care what the actual temp is, you just want to see a picture. Military/LEO devices probably have a temperature range adjustment to scale up/down according to environment. They probably have an adjustment to set the sensitivity - the difference in perceived T to go from black to white (dark green to light green; whatever).If this is finely tuned, it is like upping the contrast on your monitor.COUNTERSURVEILLANCE PROBE / MONITOR(Buy/Rent/Layaway)There is one comforting thing to consider: unless you are in the desert, there are a lot of different "things" around you, each of them with a slightly different Temperature and Emittance combination. If you can make yourself "nearly" match the most common IR surroundings and the sensitivity is set very high in order to pick up your small T/E difference, the other guy is seeing a lot more clutter around you, so your image will be just one spot on the Dalmatian.For the Ghillie fans: A man sized wad of only burlap and jute rope at 98.6 F plus or minus a few degrees will have the same E all over it. But if there was some leafage from an IR blocking camo net on one shoulder and a splotch of shredded BDU's at the waist and some foreign force camo material shredded in there somewhere in a cluster, all well supplemented with local veggies, from an IR standpoint it would look like a pile of dissimilar "stuff".If you have gotten this far, perhaps a little DECEPTION is in order to up your advantage.Remember that "Sarge WILL find something during an inspection, so ya might as well give him something so he will stop looking." If you want to determine if indeed IR detectors are out there, you might want to give them a cowboy hat to shoot at. I don't know what the E of a bare GI plastic canteen is, but if you either wrapped it with Scotch 33 electrical tape (97) from a demo/como kit or sprayed it with foot powder (96) from your ruck, and had 98 degree water (coffee? Body heat?) in it, it would make a darned good human face (97) to a distant IR imager. Topped with a BDU hat and moved about on a stick behind some intentionally inadequate screening after dark (by somebody else behind that cowboy's large rock), I suspect you would soon know the targeting capabilities of the opposition - and also acquire a muzzle flash. A piece of most anything warmer than the terrain drug remotely through the grass at night should get IR attention. Just don't pull it all the way to your position. But you get the idea.If you want to just give him/them something to worry about, scatter some old tire shreds (94) around at points distant from your position. They will look hotter than most surroundings when they are actually the same temperature. Plus, they will heat up more during sunlight, and hold their temperature for quite a while into dusk. If you can make them move a bit, so much the better. If they are behind intentionally poor screens, thus not visually or starlight identifiable, so much the better. This would be a great application for decoys specially made for the purpose - a visually camo'd, high E lollipop on a spindly, flexible stick.PRO-DTECH FREQUENCY DETECTOR(Buy/Rent/Layaway)One of the new IR illumination chemlights would do something, but I have no experience with them. I suspect one of them tripped off in front of or to the side of your position, yourself in a shadow from it, would blind any thermal imagers looking at you - like a trip flare would blind a starlight. Obviously this would be a defensive action.There have been some pretty impressive demonstrations of the capabilities of IR equipment. And it is indeed impressive stuff, but it ain't magic. It can image warm footprints on a cold roof, or a "ghost" where you leaned against a cold wall and walked away. But those images fade pretty quickly - faster than the grass will spring back up on your trail to a nest.I believe that if one person takes the time to study and understand the theory of IR systems and applies it to likely circumstances in his world and does it better than the other guy does, the first guy has an EXCELLENT chance of being the winner. That is true for sniping or bidding on a roof inspection. Even an unfavorable tilt in sophistication of equipment may be overcome with intelligent application of ingenuity. And it won't take a lot of formal training. After that, it is experience behind an imager. In your case, looking at your buddies in drill hides, and correcting each other's errors. I grant you that my "thermacam" is not a military targeting device, but if your life is professionally depending on IR avoidance, I hope you have access to IR theory training and support along with the opportunity to drill/practice with your own imagers.RF SIGNAL DETECTOR ( FREQUENCY COUNTER)(Buy/Rent/Layaway)Your questions and comments are greatly appreciated.Monty Henry, Owner Additional Resources: * Prevention and Detection of Electronic Harassment and Surveillance* Electrical Hyper-Sensitivity: The-Truth!!* How Do I Know If I’ve Been Bugged? * Targeted Individuals* Operating The Brain By Remote Control* What is BitCoin and How Does It Work?* The Creature From Jekyll Island: This Blog And Video Playlist Explains Why The U.S. Financial System is Corrupt and How It Came To Be That Way* Number of Americans Renouncing Citizenship Surges To Escape Oppressive Tax Rules* Dropping Off The Grid: A Growing Movement In America: Part I* Online Privacy Tools and Tips www.DPL-Surveillance-Equipment.com Next-Generation Bug / Microwave / ELF / Spy Phone / GSM And Camera Detectors (Buy, Rent, Layaway) tinyurl.com/2eo8mlz Open...— Spy Store Rentals (@MontyHenry1) Nanny IP (Internet) Cameras, GPS Trackers, Bug Detectors and Listening Devices, etc, (Buy / Rent / Layaway): tinyurl.com/396jlw6...— Spy Store Rentals (@MontyHenry1) NOW, look in on your home, second home, lake house or office anytime, anywhere from any internet connected PC/Lap-top or Internet active cell phone, including iphone or PDA.Watch your child's caregiver while sitting at a traffic light or lunch meeting, or check on your business security from the other side of the world. Our built-in hidden video features all digital transmissions providing a crystal clear image with zero interference. With the IP receiver stream your video over the internet through your router, and view on either a PC or smart phone. Designed exclusively for DPL-Surveillance-Equipment, these IP hidden wireless cameras come with multiple features to make the user's experience hassle-free.NOW, look in on your home, second home, lake house or office anytime, anywhere from any internet connected PC/Lap-top or Internet active cell phone, including iphone or PDA: http://www.dpl-surveillance-equipment.com/wireless_hidden_cameras.htmlWatch your child's caregiver while sitting at a traffic light or lunch meeting, or check on your business security from the other side of the world. Our built-in hidden video features all digital transmissions providing a crystal clear image with zero interference. With the IP receiver stream your video over the internet through your router, and view on either a PC or smart phone. Designed exclusively for DPL-Surveillance-Equipment, these IP hidden wireless cameras come with multiple features to make the user's experience hassle-free.• Remote Video Access• Video is Recorded Locally To An Installed SD Card (2GB SD Card included)• Email Notifications (Motion Alerts, Camera Failure, IP Address Change, SD Card Full)• Live Monitoring, Recording And Event Playback Via Internet• Back-up SD Storage Up To 32GB (SD Not Included)• Digital Wireless Transmission (No Camera Interference)• View LIVE On Your SmartPhone!Includes:* Nanny Cameras w/ Remote View* Wireless IP Receiver* Remote Control* A/C Adaptor* 2GB SD Card* USB ReceiverFACT SHEET:  HIDDEN NANNY-SPY (VIEW VIA THE INTERNET) CAMERASSpecifications:Receiver Specs:* Transmission Range of 500 ft Line Of Sight* Uses 53 Channels Resulting In No Interference* 12V Power Consumption* RCA Output* Supports up to 32gig SDCamera Specs:* 640x480 / 320x240 up to 30fps* Image Sensor: 1/4" Micron Sensor* Resolution: 720x480 Pixels* S/N Ratio: 45 db* Sensitivity: 11.5V/lux-s @ 550nm* Video System: NTSC* White Balance: Auto TrackingMake Your Own Nanny Cameras:  Make Tons Of Money In A Booming, Nearly Recession-Proof Industry!Your Primary Customers Include But Are Not Limited To Anyone In The Private Investigator, Government, Law Enforcement And/Or Intelligence Agencies Fields!* You Buy Our DVR Boards And We'll Build Your Products! (Optional)Get the DPL-Surveillance-Equipment.com widget and many other at ()Our New Layaway Plan Adds Convenience For Online ShoppersDPL-Surveillance-Equipment's layaway plan makes it easy for you to buy the products and services that you want by paying for them through manageable monthly payments that you set. Our intuitive calculator allows you to break down your order's purchase price into smaller payment amounts. Payments can be automatically deducted from your bank account or made in cash using MoneyGram® ExpressPayment® Services and you will receive your order once it's paid in full. Use it to plan and budget for holiday purchases, anniversaries, birthdays, vacations and more!DPL-Surveillance-Equipment's Customers can now use the convenience of layaway online to help them get through these tough economic times.We all shop now and then just to face a hard reality -- big credit card bills. However, our latest financing innovation can help you avoid that. Find out why more and more shoppers are checking out DPL-Surveillance-Equipment's e-layaway plan.If you're drooling over a new nanny camera, longing for a GPS tracker, or wishing for that spy watch, but you're strapped for cash and can't afford to do credit, do what Jennie Kheen did. She bought her iPod docking station (hidden camera w/motion-activated DVR) online using our convenient lay-away plan.Our online layaway plan works like the old-fashioned service stores used to offer. But, in Kheen's case, she went to DPL-Surveillance-Equipment.com, found the iPod docking station (hidden camera w/motion-activated DVR), then set up a payment plan."It's automatically drawn from my account," she said. "I have a budget, $208.00 a month.In three months, Kheen had paid off the $650.00 iPod docking station. She paid another 3.9 percent service fee, which amounted to about $25.35 (plus $12.00 for shipping) for a total of $687.35."You pay a little bit each month," Kheen said. "It's paid off when you get it and you don't have it lingering over your head. It's great."Flexible payment terms and automated payments make our layaway plan an affordable and fiscally responsible alternative to credit cards.1. Register:It's quick, easy and FREE! No credit check required!2. Shop:Select the items or service you want and choose "e-layaway" as your payment option. Our payment calculator makes it easy for you to set up your payment terms.3. Make Payments:Payments are made on the schedule YOU set. Check your order status or adjust your payments online in a secure environment.4. Receive Products:Receive the product shortly after your last payment. The best part, it's paid in full... NO DEBT.More Buying Power:* Our lay-away plan offers a safe and affordable payment alternative without tying up your credit or subjecting the purchase to high-interest credit card fees.No Credit Checks or Special Qualifications:* Anyone 18 years old or older can join. All you need is an active bank account.Freedom From Credit Cards:* If you are near or beyond your credit limit or simply want to avoid high interest credit card fees, our e-layaway is the smart choice for you.Flexible Payment Schedules:* Similar to traditional layaway, e-layaway lets you make regular payments towards merchandise, with delivery upon payment in full. Payments are automatically deducted from your bank account or made in cash using MoneyGram® ExpressPayment®A Tool for Planning Ahead:* Our e-layaway makes it easy for smart shoppers like you to plan ahead and buy items such as bug detectors, nanny cameras, audio bugs, gps trackers, and more!No Hidden Charges or Mounting Interest:Our e-layaway makes shopping painless by eliminating hidden charges and monthly interest fees. Our customers pay a flat transaction fee on the initial purchase price.NO RISK:* You have the right to cancel any purchase and will receive a refund less a cancellation fee. See website for details.Security and Identity Protection:DPL-Surveillance-Equipment has partnered with trusted experts like McAfee and IDology to ensure the security and integrity of every transaction. Identity verification measures are integrated into our e-layaway system to prevent fraudulent purchases.Note: Simply Choose e-Lay-Away as a "Payment Option" in The Shopping CartDPL-Surveillance-Equipment.com is a world leader in providing surveillance and security products and services to Government, Law Enforcement, Private Investigators, small and large companies worldwide. We have one of the largest varieties of state-of-the-art surveillance and counter-surveillance equipment including Personal Protection and Bug Detection Products.Buy, rent or lease the same state-of-the-art surveillance and security equipment Detectives, PI's, the CIA and FBI use. Take back control! DPL-Surveillance-Equipment.comPhone: (1888) 344-3742 Toll Free USALocal: (818) 344-3742Fax (775) 249-9320Monty@DPL-Surveillance-Equipment.comGoogle+ and GmailDPLSURVE TwitterDPLSURVEMSN Monty@DPL-Surveillance-Equipment.comAOL Instant MessengerDPLSURVE32SkypeMontyl32Yahoo Instant MessengerMontyi32Alternate Email Addressmontyi32@yahoo.comJoin my Yahoo Group!My RSS Feed

Summary

Click Here Or On Above Image To Reach Our Experts How To Avoid Thermal Imaging Cameras Now this was written to help the military snipers to be able to blend in, and avoid Thermal Imaging Cameras. It does an awesome job of explaining how they work And their weak points etc. Well we can also use the same principles talked about here, to help those of you who need to avoid the detection by Thermal Heat Detecting Cameras. Knowledge Is Power Thermal Detection, there are some pretty gloomy postings about IR detection. As a security/surveillance expert, I might shed some light (pun intended) on the subject. To qualify this, I am using the latest (I think) commercially available FLIR product.  These are my observations about IR imagers using the latest thermal imaging equipment. This is about THERMAL imaging avoidance. IR is not Xray, Hollywood be damned-it cannot detect a differential heat image through common solid materials, plastic film (black or otherwise) being an exception.  PRO-DTECH II FREQUENCY DETECTOR (Buy/Rent/Layaway) However, a good imager system can see through holes in a masking material ("IR masking" camo net). And if you are inside a dumpster, body heating the bad guy's side, he can "see" the hot spot on the dumpster's outside. But if you are not leaning (heating) against that side, he can't "see you". Your body heat will not be detected behind most readily available unholed blinding materials if you are not differentially warming/cooling those materials or allowing your own IR to reflect off of something behind/over you. BUT, if the shielding materials are alien to the surroundings, the material itself will probably stand out. See Below: Glass will not allow your THERMAL image to transmit (pass) through; same as the dumpster scenario. The lenses of IR imagers are made of exotic nonglass materials because of this. CELLPHONE DETECTOR (PROFESSIONAL) (Buy/Rent/Layaway) Every piece (cluster) of matter, including gasses, emits IR if it is above Absolute Zero (minus 459.69 degrees F). The warmer a body gets, the more IR it will emit. Eventually it will enter the visible spectrum as it gets "red hot". PRO-DTECH III FREQUENCY DETECTOR (Buy/Rent/Layaway) The surface of a piece of matter is where IR is emitted. Altering an object's surface will alter the rate at which IR is emitted. Stoveblack is a classic example. Materials physically different from each other will likely emit IR at different rates. BUT the differences may be very slight. PRO-DTECH III FREQUENCY DETECTOR (Buy/Rent/Layaway) IR imaging (read DETECTION) depends upon two objects having one or more differences in Temperature, Emissivity/Reflectivity, and Absorption of the compared objects. For this application, we can forget about Absorption, and you should all understand Temperature. Now, E + R = 100%, thus the more emissive a surface is, the less reflective. If two dissimilar objects are at the same temperature, a high E will "look" hotter to an IR imager than a low E, thus forming an image. Objects with different Temperatures and the right E's could "look" the same, thus forming NO image. Two objects with similar temperatures and similar emissivities will present an unclear, poorly defined image. Herein lies your IR strength. Here are some Emissivity values for a few materials, all in percents, all plus/minus a point or two. These are for short wavelength commercial imagers and may vary slightly for long wavelength/long range military/LE equipment. Military techies should have similar emissivity tables for your equipment.  PRO-DTECH III FREQUENCY DETECTOR (Buy/Rent/Layaway) * Human Skin: 97* Black Vinyl Electrical Tape: 97* Surface Sprayed With Dr. Scholl's Aerosol Foot Powder: 96* Water: 95* Rubber, Black, Hard: 94* Glass, Smooth: 94* Plywood, Raw Lumber: 90-95* Most Painted Surfaces (Non Aluminum Paint): 90-95* Aluminum Based Paints, Depending On Formula: 30-50* Oxidized (Blued, Parkerized) Steel: Around 90* Snow: 82-85* "Most" Organics (Vegetation): Around 80* Cloth, Untreated: Around 80 * Sand: 76 Clay: 40* Gravel: 38* Aluminum, Bare And "Shiny" (Read "Spaceblanket"): Under 10 Note the materials that cluster around 95, 80, 40, and 10  Now, to apply IR-101: In all of the scenarios below, remember that your body (or ANYTHING above absolute zero) emits IR in ALL directions. If there is a reflective object behind or beside you, it will pick up your IR and reflect it like you were a light bulb. Whichever situation and methods you use, if you have the opportunity, have an ally check you out from a flank with your best IR detection equipment. Or get the flyboys to check you out with FLIR's namesake. Do this by day AND night, as the sun will do weird (but predictable) things to the differential temps. WIRELESS/WIRED HIDDEN CAMERA FINDER III (Buy/Rent/Layaway) The BEST way to protect yourself from IR detection is get behind/under what is already there, and DON'T change the temperature of it. Since you obviously have to see and perhaps reach out, do so through the smallest portal(s) you can handle. Those "man-sized" targets detectable at 1100 yards are just that - man-sized -not the size of your nose and right eye. Remember that glass reflects some IR (100 - 94 = 6%), and the sky (space) is cold (approaching Absolute Zero), so if your scope is reflecting not sun, but sky, it will look COLD. If you have on a scope sunshade that is hot, the internal IR of the sunshade will reflect out as HOT. PRO-DTECH IV FREQUENCY DETECTOR(Buy/Rent/Layaway) I believe the GI Woodland BDU's are treated with an IR emittance reducer. If so, the "cloth" E figure in the table will change and you have to adjust for the following discussion. Or obtain untreated camo fabric or defeat that treatment (starch, I believe). The IR reducing treatment makes sense for a situation where the woods is cooler than 98.6 F. I hope the Desert Daylight BDU's are NOT treated, but the nighttime anti-starlight smocks probably should be. If your BDU's image "cold" against hot sand, you are just as "seen". I trust the techies were aware of this, and have specified correctly. But you need to confirm by looking through your equipment at your buddy against some typical backgrounds. It has been reported that "fresh" BDU's do indeed have an IR treatment that fatigues (pun) with laundering in "brightener" detergents. As a hunter, I am aware of the UV problem with animals with good night vision (is it an overabundance of rods, or cones, in the eye?) and there are detergents available via sporting goods stores that do not contain brighteners. If you need to maintain that BDU treatment, you might try that. But again, look at your buddies with your equipment. Now, in sand or vegetation (E = 76-80): If you HAVE to have artificial cover for situations where your clothing will approximate the temperature of the surroundings, you want to expose matching temperature "stuff" with a similar E (around 80). Cover as much of your skin (97) as possible with cloth (80) (remember that I don't know the E for treated BDU's). But also remember that sweaty cloth in a hot, dry background might look cold due to evaporative cooling. If you are in a hot dry situation, a tented, solid (not net), dry camo fabric applied as a screen might do the trick for IR. (Remember, same T, similar E). Visual is another problem. Keep the outlines irregular for both IR and visual. Square stuff in a curvy world stands out, no matter the technology. Fresh local vegetation in front of the screen will help both. Camo face paint is PROBABLY a high emitter, similar to regular paints (90-95), and sweat (water-95) is for sure. You really have to keep that face behind something. I don't know what a synthetic ski mask would have for an E, but I bet it is below 97. A plain old cotton tee shirt mask would work, but remember the wet/dry/cooling problem. Black ANYTHING is a good emitter. Blackened steel barrels, synthetic stocks, and painted surfaces (all E's in the 90's) should be cloth wrapped for IR and visual both. Black SWAT uniforms probably have a higher E than camo. You need to test. Dry rubber boot soles (94) are nearly as hot as your face - sock 'em (80). Old cut local vegetation will be drier, thus HOTTER due to lack of evaporation. The name of this game is to keep both the Emissivity and the Temperature of the screen and clothing the same as that of the surroundings and keep those portals small. If you are on bare clay or gravel (38-40) and are worried about aerial observation, dig in. Cover yourself with almost anything sufficiently rigid and then cover it with at least a thin but full layer of the local "dirt". This will match the E's. Once the moisture of the new cover layer equals the moisture of the surface around you (evaporative cooling), you will be in decent shape IR wise. Remember that these low E materials have a high Reflectivity, so block your own IR from getting out from under the cover. If there is a chance your body heat will affect the top surface of the dirt cover, use insulating material between you and the bottom of the "roof" to keep it the same temp as the ground around you. Foam board or sleeping bags will do that. The most critical times of day for this hide would be as the sun changes, because rapid heating/cooling of a thin layer of dirt will show up compared to the slower heating/cooling of the intact soil masses. If you can set up in a shaded spot where this will not occur, you should be in decent shape. If there is no shade, make the cover layer thick to create a heat sink approaching that of the surroundings. Wireless Camera Finder (Buy/Rent/Layaway) If there is no threat of aerial observation, and it is only a frontal threat, a "wall" of local dirt with small portals would be the best bet. Any new foxhole will print either hot or cold depending on the season and surface temperature, even if the surrounding soil is bare. The deeper soil temp is probably closer to 55 F than the surface. On snow (82-85), build a snow fort or tunnel in and make small portals. Try to dust loose snow to duplicate surface texture. Pray for new snow. If you wore an aluminized face shield behind that snow fort, it would reflect the "cold" off of the fort, and cover your hot face. This might be a shiny side application of the space blanket, and could be worth testing. Water (95) is your breath when it condenses. And it is warmer than the snow. Only thing I can think of to do here is breath through a ski mask and let it condense before it fogs up over your screen. As to "space blanket" applications: there might be some, BUT. If you are using the shiny side toward you to keep your IR from getting out, remember that the backside of it is probably not a good E match to the surroundings and it will heat/cool a lot differently than most natural things around you. If you are trying to put the shiny side out angled down to reflect the IR of the terrain right in front of you, there would be a 10% reduction in the reflection, more if it casts a shadow. If the shiny side is out and up, it will reflect the cold of outer space (or the heat of the sun) - and it is going to look REALLY weird to visual and starlight in EITHER case! I cannot think of a space blanket application that I would stake MY life on. MAGNETIC, ELECTRIC, RADIO ANDMICROWAVE DETECTOR (Buy/Rent/Layaway) In an urban situation, you will have lots of "normal" IR blockers to get under/behind. Just remember that you are an IR light bulb on the cold surfaces behind you. You cannot casually set up back in the room shadows of a windowless building anymore. Remember, glass will NOT pass through (transmit) your IR image. BUT, glass (94) has a high emissivity and will show its surface temperature rather well. If you are near the window warming it with your breath, you will reveal yourself. If you had a small barrel portal through an otherwise intact glass window, you would be IR blocked, but visually seen. A loose pane of glass back in the room shadows might be a possibility, especially for a spotter. If the room is painted (90-95) and warm (approaching 98.6 F), you might blend in IR wise. But if there is one warm window/room in an "empty" building, something is amiss. The painted walls behind you might not reflect your IR really well, but a metallic light fixture might blink every time you turn your face toward it. The best I can imagine is forget about the "room" and get behind/under something that should be there - sofas, chairs, drapes, etc. and keep your portal small. None of the above CONCEALMENT strategies are easy; none are guaranteed to make you disappear to an imager. But they will all help make you a less vivid IR image, thus less detectable. IR imagers may or may not have an adjustment to key in the emissivity for scanning and reading temperatures. I doubt military/LE targeting devices would have that - you don't care what the actual temp is, you just want to see a picture. Military/LEO devices probably have a temperature range adjustment to scale up/down according to environment. They probably have an adjustment to set the sensitivity - the difference in perceived T to go from black to white (dark green to light green; whatever).If this is finely tuned, it is like upping the contrast on your monitor. COUNTERSURVEILLANCE PROBE / MONITOR(Buy/Rent/Layaway) There is one comforting thing to consider: unless you are in the desert, there are a lot of different "things" around you, each of them with a slightly different Temperature and Emittance combination. If you can make yourself "nearly" match the most common IR surroundings and the sensitivity is set very high in order to pick up your small T/E difference, the other guy is seeing a lot more clutter around you, so your image will be just one spot on the Dalmatian. For the Ghillie fans: A man sized wad of only burlap and jute rope at 98.6 F plus or minus a few degrees will have the same E all over it. But if there was some leafage from an IR blocking camo net on one shoulder and a splotch of shredded BDU's at the waist and some foreign force camo material shredded in there somewhere in a cluster, all well supplemented with local veggies, from an IR standpoint it would look like a pile of dissimilar "stuff". If you have gotten this far, perhaps a little DECEPTION is in order to up your advantage. Remember that "Sarge WILL find something during an inspection, so ya might as well give him something so he will stop looking." If you want to determine if indeed IR detectors are out there, you might want to give them a cowboy hat to shoot at. I don't know what the E of a bare GI plastic canteen is, but if you either wrapped it with Scotch 33 electrical tape (97) from a demo/como kit or sprayed it with foot powder (96) from your ruck, and had 98 degree water (coffee? Body heat?) in it, it would make a darned good human face (97) to a distant IR imager. Topped with a BDU hat and moved about on a stick behind some intentionally inadequate screening after dark (by somebody else behind that cowboy's large rock), I suspect you would soon know the targeting capabilities of the opposition - and also acquire a muzzle flash. A piece of most anything warmer than the terrain drug remotely through the grass at night should get IR attention. Just don't pull it all the way to your position. But you get the idea. If you want to just give him/them something to worry about, scatter some old tire shreds (94) around at points distant from your position. They will look hotter than most surroundings when they are actually the same temperature. Plus, they will heat up more during sunlight, and hold their temperature for quite a while into dusk. If you can make them move a bit, so much the better. If they are behind intentionally poor screens, thus not visually or starlight identifiable, so much the better. This would be a great application for decoys specially made for the purpose - a visually camo'd, high E lollipop on a spindly, flexible stick. PRO-DTECH FREQUENCY DETECTOR(Buy/Rent/Layaway) One of the new IR illumination chemlights would do something, but I have no experience with them. I suspect one of them tripped off in front of or to the side of your position, yourself in a shadow from it, would blind any thermal imagers looking at you - like a trip flare would blind a starlight. Obviously this would be a defensive action. There have been some pretty impressive demonstrations of the capabilities of IR equipment. And it is indeed impressive stuff, but it ain't magic. It can image warm footprints on a cold roof, or a "ghost" where you leaned against a cold wall and walked away. But those images fade pretty quickly - faster than the grass will spring back up on your trail to a nest. I believe that if one person takes the time to study and understand the theory of IR systems and applies it to likely circumstances in his world and does it better than the other guy does, the first guy has an EXCELLENT chance of being the winner. That is true for sniping or bidding on a roof inspection. Even an unfavorable tilt in sophistication of equipment may be overcome with intelligent application of ingenuity. And it won't take a lot of formal training. After that, it is experience behind an imager. In your case, looking at your buddies in drill hides, and correcting each other's errors. I grant you that my "thermacam" is not a military targeting device, but if your life is professionally depending on IR avoidance, I hope you have access to IR theory training and support along with the opportunity to drill/practice with your own imagers. RF SIGNAL DETECTOR ( FREQUENCY COUNTER)(Buy/Rent/Layaway) Your questions and comments are greatly appreciated. Monty Henry, Owner (function () { var articleId = fyre.conv.load.makeArticleId(null); fyre.conv.load({}, [{ el: 'livefyre-comments', network: "livefyre.com", siteId: "345939", articleId: articleId, signed: false, collectionMeta: { articleId: articleId, url: fyre.conv.load.makeCollectionUrl(), } }], function() {}); }()); Additional Resources: * Prevention and Detection of Electronic Harassment and Surveillance * Electrical Hyper-Sensitivity: The-Truth!! * How Do I Know If I’ve Been Bugged?  * Targeted Individuals * Operating The Brain By Remote Control * What is BitCoin and How Does It Work? * The Creature From Jekyll Island: This Blog And Video Playlist Explains Why The U.S. Financial System is Corrupt and How It Came To Be That Way * Number of Americans Renouncing Citizenship Surges To Escape Oppressive Tax Rules * Dropping Off The Grid: A Growing Movement In America: Part I * Online Privacy Tools and Tips www.DPL-Surveillance-Equipment.com (function() { var po = document.createElement('script'); po.type = 'text/javascript'; po.async = true; po.src = 'https://apis.google.com/js/plusone.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(po, s); })(); Next-Generation Bug / Microwave / ELF / Spy Phone / GSM And Camera Detectors (Buy, Rent, Layaway) tinyurl.com/2eo8mlz Open... — Spy Store Rentals (@MontyHenry1) Nanny IP (Internet) Cameras, GPS Trackers, Bug Detectors and Listening Devices, etc, (Buy / Rent / Layaway): tinyurl.com/396jlw6... — Spy Store Rentals (@MontyHenry1) NOW, look in on your home, second home, lake house or office anytime, anywhere from any internet connected PC/Lap-top or Internet active cell phone, including iphone or PDA. Watch your child's caregiver while sitting at a traffic light or lunch meeting, or check on your business security from the other side of the world. Our built-in hidden video features all digital transmissions providing a crystal clear image with zero interference. With the IP receiver stream your video over the internet through your router, and view on either a PC or smart phone. Designed exclusively for DPL-Surveillance-Equipment, these IP hidden wireless cameras come with multiple features to make the user's experience hassle-free. NOW, look in on your home, second home, lake house or office anytime, anywhere from any internet connected PC/Lap-top or Internet active cell phone, including iphone or PDA: http://www.dpl-surveillance-equipment.com/wireless_hidden_cameras.html Watch your child's caregiver while sitting at a traffic light or lunch meeting, or check on your business security from the other side of the world. Our built-in hidden video features all digital transmissions providing a crystal clear image with zero interference. With the IP receiver stream your video over the internet through your router, and view on either a PC or smart phone. Designed exclusively for DPL-Surveillance-Equipment, these IP hidden wireless cameras come with multiple features to make the user's experience hassle-free. • Remote Video Access • Video is Recorded Locally To An Installed SD Card (2GB SD Card included) • Email Notifications (Motion Alerts, Camera Failure, IP Address Change, SD Card Full) • Live Monitoring, Recording And Event Playback Via Internet • Back-up SD Storage Up To 32GB (SD Not Included) • Digital Wireless Transmission (No Camera Interference) • View LIVE On Your SmartPhone! Includes: * Nanny Cameras w/ Remote View * Wireless IP Receiver * Remote Control * A/C Adaptor * 2GB SD Card * USB Receiver FACT SHEET:  HIDDEN NANNY-SPY (VIEW VIA THE INTERNET) CAMERAS Specifications: Receiver Specs: * Transmission Range of 500 ft Line Of Sight * Uses 53 Channels Resulting In No Interference * 12V Power Consumption * RCA Output * Supports up to 32gig SD Camera Specs: * 640x480 / 320x240 up to 30fps * Image Sensor: 1/4" Micron Sensor * Resolution: 720x480 Pixels * S/N Ratio: 45 db * Sensitivity: 11.5V/lux-s @ 550nm * Video System: NTSC * White Balance: Auto Tracking Make Your Own Nanny Cameras:  Make Tons Of Money In A Booming, Nearly Recession-Proof Industry! Your Primary Customers Include But Are Not Limited To Anyone In The Private Investigator, Government, Law Enforcement And/Or Intelligence Agencies Fields! * You Buy Our DVR Boards And We'll Build Your Products! (Optional) if (WIDGETBOX) WIDGETBOX.renderWidget('a37c3242-37e2-4596-9572-786e643c3c89');Get the DPL-Surveillance-Equipment.com widget and many other at () Our New Layaway Plan Adds Convenience For Online Shoppers DPL-Surveillance-Equipment's layaway plan makes it easy for you to buy the products and services that you want by paying for them through manageable monthly payments that you set. Our intuitive calculator allows you to break down your order's purchase price into smaller payment amounts. Payments can be automatically deducted from your bank account or made in cash using MoneyGram® ExpressPayment® Services and you will receive your order once it's paid in full. Use it to plan and budget for holiday purchases, anniversaries, birthdays, vacations and more! DPL-Surveillance-Equipment's Customers can now use the convenience of layaway online to help them get through these tough economic times. We all shop now and then just to face a hard reality -- big credit card bills. However, our latest financing innovation can help you avoid that. Find out why more and more shoppers are checking out DPL-Surveillance-Equipment's e-layaway plan. If you're drooling over a new nanny camera, longing for a GPS tracker, or wishing for that spy watch, but you're strapped for cash and can't afford to do credit, do what Jennie Kheen did. She bought her iPod docking station (hidden camera w/motion-activated DVR) online using our convenient lay-away plan. Our online layaway plan works like the old-fashioned service stores used to offer. But, in Kheen's case, she went to DPL-Surveillance-Equipment.com, found the iPod docking station (hidden camera w/motion-activated DVR), then set up a payment plan. "It's automatically drawn from my account," she said. "I have a budget, $208.00 a month. In three months, Kheen had paid off the $650.00 iPod docking station. She paid another 3.9 percent service fee, which amounted to about $25.35 (plus $12.00 for shipping) for a total of $687.35. "You pay a little bit each month," Kheen said. "It's paid off when you get it and you don't have it lingering over your head. It's great." Flexible payment terms and automated payments make our layaway plan an affordable and fiscally responsible alternative to credit cards. 1. Register: It's quick, easy and FREE! No credit check required! 2. Shop: Select the items or service you want and choose "e-layaway" as your payment option. Our payment calculator makes it easy for you to set up your payment terms. 3. Make Payments: Payments are made on the schedule YOU set. Check your order status or adjust your payments online in a secure environment. 4. Receive Products: Receive the product shortly after your last payment. The best part, it's paid in full... NO DEBT. More Buying Power: * Our lay-away plan offers a safe and affordable payment alternative without tying up your credit or subjecting the purchase to high-interest credit card fees. No Credit Checks or Special Qualifications: * Anyone 18 years old or older can join. All you need is an active bank account. Freedom From Credit Cards: * If you are near or beyond your credit limit or simply want to avoid high interest credit card fees, our e-layaway is the smart choice for you. Flexible Payment Schedules: * Similar to traditional layaway, e-layaway lets you make regular payments towards merchandise, with delivery upon payment in full. Payments are automatically deducted from your bank account or made in cash using MoneyGram® ExpressPayment® A Tool for Planning Ahead: * Our e-layaway makes it easy for smart shoppers like you to plan ahead and buy items such as bug detectors, nanny cameras, audio bugs, gps trackers, and more! No Hidden Charges or Mounting Interest: Our e-layaway makes shopping painless by eliminating hidden charges and monthly interest fees. Our customers pay a flat transaction fee on the initial purchase price. NO RISK: * You have the right to cancel any purchase and will receive a refund less a cancellation fee. See website for details. Security and Identity Protection: DPL-Surveillance-Equipment has partnered with trusted experts like McAfee and IDology to ensure the security and integrity of every transaction. Identity verification measures are integrated into our e-layaway system to prevent fraudulent purchases. Note: Simply Choose e-Lay-Away as a "Payment Option" in The Shopping Cart DPL-Surveillance-Equipment.com is a world leader in providing surveillance and security products and services to Government, Law Enforcement, Private Investigators, small and large companies worldwide. We have one of the largest varieties of state-of-the-art surveillance and counter-surveillance equipment including Personal Protection and Bug Detection Products. Buy, rent or lease the same state-of-the-art surveillance and security equipment Detectives, PI's, the CIA and FBI use. Take back control! DPL-Surveillance-Equipment.com Phone: (1888) 344-3742 Toll Free USA Local: (818) 344-3742 Fax (775) 249-9320 Monty@DPL-Surveillance-Equipment.com Google+ and Gmail DPLSURVE Twitter DPLSURVE MSN  Monty@DPL-Surveillance-Equipment.com AOL Instant Messenger DPLSURVE32 Skype Montyl32 Yahoo Instant Messenger Montyi32 Alternate Email Address montyi32@yahoo.com Join my Yahoo Group! My RSS Feed

Subtitle
Click Here Or On Above Image To Reach Our Experts How To Avoid Thermal Imaging Cameras Now this was written to help the military snipers to be able to blend in, and avoid Thermal Imaging Cameras. It does an awesome job of explaining how they work And th
Duration
Publishing date
2016-08-30 20:10
Link
http://dpl-surveillance-equipment.blogspot.com/2016/08/how-to-avoid-thermal-imaging-cameras.html
Contributors
  noreply@blogger.com (DPL-Surveillance-Equipment)
author  
Enclosures
http://www.dailymotion.com/videowall/playlist/x2ji94_montyl32_listening-devices-buy-rent-layaway&cols=7&rows=2&brand=bottom
application/x-shockwave-flash